$50
here we have a new Brushless ESC / Motor Combo it is a matched set from Turnigy
the ESC is 25 Amps / 50 Amp Burst ,and is good for 2s to 4s Lipo with Bec circut.
The motor is an NTM Prop Drive 35-30 Outrunner for planes
or whatever you like it is 1100 Kv and can swing an 8" to 12" prop
serious interests can call my cell at thank you
here are the specs below
The Turnigy TY-P1 25Amp ESC is a stand out performer. Using quality IR HEXFET® Power MOSFETs developed in the USA, this ESC is cable of handling current draw in excess of 40 amps. However this in house designed ESC was developed and produced by the HobbyKing engineering team with one goal in mind, quality and reliability. Rather than over rate the ESC and push it to the limit with a larger heat-sink, as many companies do, we wanted to design a Speed controller for those looking for a bullet proof solution. We use SMT technology rather than hand soldering to produce consistent quality and reliability each and every time. The TY-P1 25A ESC also features independent voltage regulators (One for the BEC and one for the MCU) this ensures the MCU will remain powered in the event of a high momentary amp draw from the BEC circuit and vise versa. An XT-60 battery connector and 3.5mm bullet connectors have been pre-soldered for convenience.
Specs:
Cont. Current: 25A
Burst Current: 50A
BEC: 5volts / 2amps
Weight: 42.5 Gram (including wires and plugs)
Battery Plug: XT-60
Motor Plug: 3.5mm Bullet Connector
Programming Options:
Brake (OFF/ON).
Cut-off Type (Soft-cut/Cut-off).
Cut-off Voltage (Low / Middle / High ).
Start Mode (Normal / Soft / Very Soft ).
Timing Mode (Low / Middle / High).
Cell (Auto, 2S, 3s, 4S).
NTM Prop Drive motors are rock-solid performance outrunners with tight windings, quality bearings, correctly rated magnets, balanced stator and flux rings, tool-steel shafts plus they are QC checked at 14 points, from material processing all the way through to final dyno test.
Because we design and build these motors completely in-house (from 3D/2D drawing to materials sourcing, machining, balancing, final assembly and dyno) we can completely control production and ensure product consistency from design right through to shipping the product to you. The removal of middle-men has meant we can drive better value to the market and retail these motors at factory(our) prices! All performance figures are real and tested on our own motor dynos.
Perfect Kv and size for quadcopters!
Our QC engineers check and balance each motor before shipping to the HobbyKing.com warehouse.
Specs:
Model: NTM Prop Drive Series 35-30 1100kv
Kv: 1100rpm/v
Max current: 32A
Max Power: 350W @ 12v (3S) / 380 @ 15v (4S)
Shaft: 4mm
Weight: 88g
ESC: 40
Cell count: 3s~4s Lipoly
Bolt holes: 18.9mm & 25mm
Bolt thread: M3
Connection: 3.5mm Bullet-connector
Prop Tests:
8x4 - 14.8v - 251W - 17A
8x4 - 11.1v - 121W - 11A
9x6 - 11.1v - 178W - 16A
9x6 - 14.8v - 355W - 24A
10x5 - 11.1v - 200W - 18A
10x5 - 14.8v - 385W - 26A
11x5.5 - 11.1v - 200w - 20A
12x6 - 11.1v - 266w - 26A
